AirScape Engineer's Blog » Sound

Sound Reduction part 4 – Ducted Models

paul — Fri, 30 Jul 2010 15:30:56 +0000

The final step on our journey of sound reduction brings us to ducted AirScape models. As you already know the ducted design of the 2.5 WHF, 2.5e WHF, 4.4e WHF, 4.5 WHF, and the Kohilo 2.8 allow for maximum airflow with a minimum of noise. Improper installation of these models can increase their sound levels. We touched on this subject earlier in the blog “4.5 Installation – Maximize Airflow, Minimize Noise.” There are a few things you need to consider when installing a ducted model.

90 DEGREE BEND - The 90 degree bend should be as smooth as possible to maintain the 20″ diameter of the ductwork. Kinking the ductwork will increase the sound level and reduce airflow because the air does not have a smooth path to the fan.

EXTENSION - It is important to extend the ductwork as far as possible away from the damper box. This needs to be done without distorting the 90 degree bend in the ductwork. Extending the ductwork fully moves the sound source (the fan) to the farthest point from the living space.

D-RINGS - The 2.5, 2.5e, and 4.4e fans have D-rings which are used to hang the fan from the attic rafters. Only 4 of the 8 D-rings are used in the installation. The unused D-rings should be taped down to avoid excess rattling.

PART 1 / PART 2 / PART 3 / PART 4

Sound Reduction part 2 – Raised Frame

paul — Fri, 16 Jul 2010 23:55:45 +0000

You may consider a raised frame for your 1.0 or 1.7 WHF for additional sound reduction. The raised frame increases the distance between the fan and living space. Like our ducted models, making the fan slightly more remote from the living space will decrease the overall sound level. The height of the frame will depend on the total vertical clearance of your attic. The construction is very simple and will add a few additional steps to your installation.

STEP 1: We made a raised frame using some scrap 2×4′s. The inside dimension is 14.5”x22.5” matching the framed opening. Secure the raised frame to the attic floor.

STEP 2: Caulk all of the frame gaps and joints. Place the provided foam rubber gasket on top of the raised frame.

STEP 3: Secure the unit to the framing (1.7 WHF shown). From the living space caulk all gaps between the unit and the framing.

STEP 4: It’s not a bad idea to add some insulation around the raised frame. You can now follow the remaining steps in the installation and operation manual to finish your install.

PART 1 / PART 2

Sound Reduction part 1 – Duct Board

paul — Wed, 14 Jul 2010 19:02:56 +0000

Your AirScape is already the quietest whole house fan on the market, but there are a few install techniques to make it even quieter. We’ve decided to dedicate a few blog entries to some techniques that will help with sound reduction.

We’ll start with a simple installation step that works with all AirScape models. You can easily line the inside of the framed opening (between the unit and grille) with duct board. Duct board is a resin bonded fiberglass board that has acoustic and insulative properties. The fibrous mat surface of the duct board helps absorb sound and allows for the smooth passage of air. The fiberglass body of this material usually has an insulation value of R-4. The duct board can easily be installed in new or existing installations using either adhesive or screws and flat washers. In fact, we love this material so much we lined one wall of our new office with it (our lead engineer’s rants on energy efficiency, life, and politics are a little more muffled now).

Duct board resources:

http://www.specjm.com/products/ductboard/enviroaire.asp

http://www.owenscorningcommercial.com/data/products/product.aspx?id=271

http://www.certainteed.com/products/insulation/hvac-mechanical/317382

PART 1 / PART 2

4.5 Installation – Maximize Airflow, Minimize Noise

paul — Tue, 02 Feb 2010 19:46:15 +0000

Recently we have been using our new and improved sound testing chamber to make sound comparison videos of our different models. The shooting of these videos reminded us that the set up of the ducted models will make a significant difference in the CFM and noise levels. Basically, improper installation will decrease the unit CFM and increase the amount of noise. Some numbers for comparison:

AirScape 4.5 improper installation - high 59 dBA / low 50 dBA

AirScape 4.5 proper installation - high 55 dBA /low 46 dBA ……A 4 dBA difference!

The photo above shows the correct install dimensions for the 4.5 WHF. You will notice that we have a nice even bend and the ductwork is fully extended (Note that we used an extra length of the provided chain to help support the bend). It is important to maintain the 20″ diameter of the duct through the 90 degree bend. This will ensure that you get unrestricted airflow through the duct and will help disrupt the sound waves. You also want to make sure the duct and fan are fully extended from the 90 degree bend. This moves the fan to the furthest point from the grill opening, thus decreasing the decibel level.

Airscape 2.5/2.5e installation: The install dimensions for the AirScape 2.5/2.5e are very similar. The duct should be 21″ from the attic floor. It should extend 44″ from the 90 degree bend to the fan (you may be able to extend it to 48″ if the bend is supported as shown in the photo above). The top of the fan should be 44″ from the attic floor.